NES MiHealth V1 Troubleshooting Guide

For the NES miHealth (Gen 1)

Did you know?

? You can find helpful training videos, the miHealth manual as well as helpful protocol charts on the miHealth page in your portal. This page is accessible in your E4L portal in the Education section. ?

If your miHealth device starts acting a little differently or turns off during a cycle it may need to be reset. Just like a computer benefits from being restarted, the miHealth benefits from being reset, especially if it is used often. See Soft Reset below.


Basic Maintenance

Calibrating Electrodes

You will need to calibrate electrodes any time you use external electrodes and any time you switch back to internal electrodes. Other times you may want to calibrate the electrodes would be after traveling or after big weather changes. If you use your device daily in your practice, you may want to calibrate the electrodes once per week just to make sure your device is perfectly calibrated.

To calibrate the electrodes, tap the wrench icon on the bottom right side of the screen to access the settings menu and select Calibrate Electrodes.

Soft Reset

It is a good idea to do a soft reset regularly if you use your device daily with patients or if your device starts to act a little differently. (less responsive, screen flickers, the device turns off during a cycle)

This simple reset uses the two side buttons (intensity buttons on the left side of your device) and the on/off button.

With the miHealth off, press and hold the two side buttons and turn on your device. Keep the side buttons pressed until the screen turns on. Here is a video demonstration of the Soft Reset.

Calibrating the screen

If your screen presses become less accurate or the screen is unresponsive you can re-calibrate the screen. The screen calibration process adds one button press to the soft reset described above. You will be using the on/off button, the two side buttons, and the top right button on the face of your device. 

With the miHealth off, press all four buttons at the same time, hold for 2 seconds, release the on/off button, and the two side buttons, hold the top right button for another second, then release.

If the presses were successful, you will see a 3x in the top left corner of your screen. Use the Stylus to tap in the top left corner three times, then do the same in the bottom right corner. Here is a video demonstration of the Screen Calibration.

Advanced Maintenance

If the electrode calibration and soft reset do not help to bring your device back to optimal functioning you will want to take these next steps. These steps require the use of the BioSync software. The installation file is available for download in your E4L portal under Resources.

Forced Update

A forced update is performed using BioSync software and a computer. The forced update will refresh your miHealth operating system and may be needed if the soft reset is not solving your device issues. The forced update is also needed if you change your device battery and there is a key symbol on your screen.

The forced update needs to be set by the E4L support team first. To do so please open a support ticket by visiting https://help.E4L.com/ scrolling to the bottom of the page and selecting Submit a Request

You will need to ask for a Forced Update and provide your E4L user email and the Unit id of your miHealth. The unit ID consists of numbers and letters. It can be found on the settings screen by selecting miUnit. It is also displayed on the sticker inside the battery compartment of your device under the barcode (second series of numbers and letters).

Once you receive a positive response from the support team, you can proceed. Open BioSync, connect your miHealth, turn your miHealth on, select miHealth updater on BioSync, and proceed with the update.

Factory Reset

You may at times be asked to do a Factory Reset on your device. The factory reset will re-install the operating system on your device. This should only be performed if asked to do so by a support team member. Keep in mind that a factory reset will remove any custom folders you have created. You will need to re-create any custom folders you want on your device after the reset is complete. Instructions for the factory reset can be found here: https://e4l-help.freshdesk.com/a/solutions/articles/206000078934


Still need help?

Our assistant can answer most questions straight away, and passes anything it can't to the support team.